How do you adjust the idle on Poulan Woodshark

Turn the screw with a flat-head screwdriver. If the saw is idling too slow, turn the screw clockwise to increase engine speed. If the chain begins turning, turn the screw counterclockwise until it stops. Try to find the sweet spot — where the engine runs smoothly without engaging the chain.

What is the T screw on a Poulan chainsaw?

The screw on top — marked “T” — is for adjusting the fuel mixture while the engine is idling. Of the two underneath it, the one on the left is for adjusting the mixture when the engine is running a low speed, and the one on the right is for making the same adjustment when the engine is running at high speed.

Why does my Poulan chainsaw keeps stalling?

The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. … This sticky fuel can clog up the fuel filter and cause the engine to stall. If old fuel was left in the chainsaw, drain the old fuel from the fuel tank and replace the fuel filter.

What is the H and L on a carburetor?

They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).

Why does my chainsaw stall when I give it gas?

Carburetor Adjustment An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.

How do you adjust the idle on a Poulan chainsaw?

Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.

What is the spark plug gap on a Poulan chainsaw?

A: The spark plug gap on all products is . 025-inch.

How do I adjust idle speed?

Turn the idle screw, now exposed from the protective rubber coating, in order to adjust the idle. Loosen the screw in a counter-clockwise fashion to increase idle speed or tighten it in a clockwise manner in order to decrease the idle speed.

How does the idle adjustment screw work?

Once the air fuel mixture screws have been properly adjusted, and the engine runs smoothly both at idle, and when revved, it is time to locate the idle mixture screw. The idle mixture screw controls the air fuel mixture at idle speed, and often is located near the throttle plate.

Where is the idle screw on a chainsaw?

The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.

Article first time published on

What does the T stand for on a chainsaw?

The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.

How do I keep my chainsaw running?

1. Keep your Chain Sharp: Keeping your chain sharp is probably the easiest and most effective way to extend the life of your saw. …
2. Flip your Bar: …
3. Drain your Gas: …
4. Check your Sprocket: …
5. Keep a watchful Eye:

Why does my chainsaw bog down when I pull the trigger?

Many chainsaw operators first notice a problem with chainsaws bogging down when they’re using the chainsaw under load, and this is usually the result of poor air circulation. This issue is caused by a clogged air filter on the chainsaw. … Wash the air filter in soapy water until the air filter comes completely clean.

How often should you change the spark plug in a chainsaw?

A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.

How long will a Poulan Pro chainsaw last?

Re: Poulan Pro Chainsaws To make up for the low price they may have lower quality parts, especially internal engine parts. Most of those discount saws have about 40 hours expected useful life built in to them. Stihl’s, in comparison, are either 500 or 1000, depending on the model.

Can't get my Poulan chainsaw started?

If your Poulan chain saw won’t start, the first thing to check is the fuel. … Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.

How does a diaphragm work on a carburetor?

The diaphragm is connected to the needle valve and as it moves inward it opens the needle valve to admit more fuel, thus replenishing the fuel as it is consumed. As fuel is replenished the diaphragm moves out due to fuel pressure and a small spring, closing the needle valve.

Where is the idle screw on a carburetor?

The idle speed screw (arrow 1) is located on the primary linkage. The idle metering adjustment screws (arrow 2) are located on the primary metering block on most Holley carburetors. A typical starting location for these idle mixture screws is between 1 and 1 ½ turns out from fully seated.

Why is my idle screw not working?

It is either a linkage problem or the butterfly plate is physically stuck. If the choke high idle adjuster and the throttle positioner (if you have one) adjuster screws are not the problem, it is time to remove the carb and check the linkage and butterflies to make sure that they shut properly.

How do you adjust the idle screw on a motorcycle?

Loosen the screw counterclockwise to turn the idle speed down. Turning the screw counterclockwise to decrease the idle speed and pull it back. Turn the screw 1-5 times based on how drastically you want to trim the idle speed on your bike. Inspect the tachometer after adjusting the screw if you have a gauge.

Which way do I turn idle screw to idle?

Set idle speed adjusting screw, clockwise to increase rpm, counter-clockwise to decrease rpm. Idle rpm range should be 950 to 1050 rpms. Adjust idle mixture by turning idle mixture screw slowly clockwise until the engine runs poorly.

How do you adjust the idle on a 2010 crf250r?

Turn the knob counter-clockwise to raise the idle speed.

What should a motorcycle idle at?

A healthy RPM for most motorcycles should be between 700 RPM’s – 1,000 RPM’s. Some motorcycles are a little different from each other, so be sure to check your owner’s manual to make sure. But usually you can tell by how it sounds. Any idle higher than 1,500 RPM’s is considered high and should be adjusted.