How do you apply RockSolid

RockSolid Dry Time & Clean-up Surface should be ready for foot traffic in 8-10 hours and vehicle traffic in 24-36 hours, depending upon temperature and humidity.

How long does rock solid take to dry?

RockSolid Dry Time & Clean-up Surface should be ready for foot traffic in 8-10 hours and vehicle traffic in 24-36 hours, depending upon temperature and humidity.

Is rock solid or epoxy shield better?

RockSolid is our highest end. We also have one part water-based coatings again, but you’re not going to get the longevity that you get with a two-part epoxy like RockSolid,” she said. … This great hard surface is twenty times stronger than regular two-part epoxy paint — even stronger than our EpoxyShield.

How long does RockSolid last?

If Temp is 40-75°F:If Temp is 76-90°F:Pot life after mixing: 1 hour (do not use product after 1 hour)Pot life after mixing: 45 minutes (do not use product after 45 minutes)Best results: 12pm (or when temperatures are rising)Best results: coat early morning (before 9AM)

Can you recoat RockSolid?

A second coat of RockSolid® Floor Coatings can be applied. The floor can be recoated after 8-12 hours and before 7 days without sanding the surface for proper adhesion of the second coat. … If more than 7 days has passed, sand the surface with 60-80 grit sandpaper before applying the second coat.

How long does Polycuramine take to cure?

Cure Time: The recommended cure time is 8-10 hours for foot traffic and 24 hours for vehicle traffic. Due to our high temperature that day, the paint dried pretty quickly for us.

How do you remove Rust Oleum RockSolid?

Apply RockSolid Heavy Duty Cleaner to the entire floor and allow it to soak into the surface for 5-10 minutes, misting the surface as needed to keep it damp. Work the product into the surface with a stiff bristle brush or broom. Rinse the surface thoroughly with water or power wash to remove all cleaner residue.

Is RockSolid water based?

It’s a water-based acrylic clear that will not perform well in a garage environment. One of the primary rules for concrete coatings is that the clear coat should be just as durable in not more so than the color coat. RockSolid clear would be the correct clear coat to use.

Why is my epoxy floor still sticky?

If the entire floor, or most of the floor, remains tacky after the manufacturer’s stated drying time, the cause is almost assuredly a cold floor. The epoxy compound will harden at the proper temperature, but drying will slow down, or even stop, if the floor is too cold.

Can you epoxy over Polycuramine?

Polycuramine Coatings combine the best of Polyurea, Urethane and Epoxy chemistries. This gives them a huge edge over Epoxy…and Polyurea for that matter.

Article first time published on

What is a polyaspartic coating?

What is a Polyaspartic Coating? Corrosionpedia defines polyaspartic as a protective layer of aliphatic polyurea, described as a 100% solid, fast curing, two component, UV resistant coating system. Surfaces are covered by spraying, painting or plastering to prevent corrosion and erosion.

Is epoxy or Polycuramine better?

Polycuramine is 20 times stronger than epoxy. With its resistance to salt, oil, gas and other harsh chemicals, this is one of the toughest floor coatings on the planet. It’s easy to maintain and will last a lifetime while still looking fantastic.

Can rustoleum rock solid be used outside?

RockSolid® Polycuramine® & EpoxyShield Floor Coatings are not recommended for exterior use because they are not designed to withstand the outdoor elements and do not contain UV protection. If RockSolid® or EpoxyShield is applied to an outdoor surface, it will likely yellow and weather over time.

Is rustoleum rock solid water based?

Rust-Oleum RockSolid Tintable Water-based Resurfacer (1-Gallon)

Can rustoleum rock solid be used on wood?

RockSolid 2X Solid Stain is recommended for use on lightly worn wood surfaces. New wood needs to weather at least 6 months before application. Concrete: RockSolid 2X Solid Stain should only be applied to structurally sound broom swept or porous concrete. … New concrete surfaces need to cure 30 days before application.

When can I apply a second coat of Rustoleum?

If you are concerned, you can apply a second coat of Rust-Oleum HOME Top Coat. To do so, simply wait until the first Top Coat is dry to the touch (1-2 hours) before applying the second Top Coat. We recommend the second coat to be applied within 24 hours of the first.

Does tacky epoxy ever cure?

You cannot leave the sticky resin, as it will not harden after time, it will remain sticky. You will have to either throw your item away or fix the problem. In order to avoid the problem all together make sure to do the following: You must measure out your resin and hardener precisely.

What do you do if epoxy doesn't Harden?

Try moving your piece to a warmer spot: if it doesn’t dry, re-pour with a fresh coat of resin. Soft, sticky spots: if you have sticky spots on an otherwise perfectly cured surface, you may have scraped out unmixed resin or hardener from your mixing container when you poured.

What causes fish eyes in epoxy floors?

Substrate contamination is the most common problem that causes fish eyes and pin holes in epoxy seal coats. Dust, dirt, wax, silicones, even the oil from your fingers when touching the part prior to sealing with epoxy will deter epoxy resins from laying flat and curing with a perfectly smooth surface.

How long does rustoleum garage floor last?

The average life expectancy of these floors is 3 – 5 years before they start to show their age and even longer if you apply a second coat of clear.

How long does polyaspartic last?

The two biggest advantages of a polyaspartic garage floor coating are fast curing time and low-temperature cure. Polyaspartic coating cures very fast, with a pot life of 10 to 120 minutes depending on the formulation. Typical polyaspartic floor coatings are applied in just two to three coats.

Is polyaspartic slippery?

Even at 3 to 5 mils in thickness, polyaspartic coatings can be very slippery when wet. The material will meet the ASTM coefficient of friction when dry, but will not when wet. This is especially important to consider if they are going to be used on exterior surfaces or on surfaces that may get wet periodically.

How long does polyaspartic take to dry?

It will take approximately 2-4 hours for the surface of the floor to dry at 77° F or warmer, or 4-6 hours when cooler. Wait 6-8 hours before allowing light foot traffic.

Is Polycuramine flexible?

Polycuramine® provides incredible abrasion and chemical resistance. This product combines key attributes from multiple chemistries into one indestructible, self-leveling, flexible, fast curing, high gloss coating system.