How far can toilet be from main stack

If the waste line is 4 inches in diameter, the toilet can be as far as 10 feet from the stack. Maintaining these critical distances ensures the stack can handle the new toilet.

How far can toilet be from sewer line?

If the toilet is less than six feet from the stack, tie the waste line from the new toilet directly into the stack. The toilet can be as far as 10 feet from the stack if the waste line is 4 inches.

How far can you move a toilet with an offset flange?

For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.

How far can a drain be from the stack?

There is a vent between the sink P-trap and the point where the waste line goes to the main sewer. The vent can’t be more than 2 1/2 feet from the trap if the waste line has a diameter of 1 1/2 inches. The critical distance is 3 1/2 feet if the waste line is 1 1/2 inches.

Can you move toilet location?

Moving the toilet is not a change to be taken lightly. But if needed, it can be accomplished with substantial plumbing work and a great deal of peripheral work, such as opening up a floor or ceiling, rerouting pipes and drain flange, and re-installing the toilet and other fixtures.

How far can a toilet be from a wet vent?

According to the UPC, the distance between your trap and the vent should be no more than 6 feet.

Can a toilet be moved 6 inches?

Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side.

How many toilets can be on a 3 inch drain?

There is one answer. The International Plumbing Code requires 5 Drainage Fixture Units in a bathroom group. It’s good for 20 DFU’s or 4 bathroom groups.

How far can P trap be from drain?

According to the International Residential Code, the maximum vertical distance between the sink drain and the entrance to the p-trap is 24 inches.

Is it expensive to relocate a toilet?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.

Article first time published on

Can you replace a 10 inch rough in toilet with a 12 inch rough in toilet?

The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.

How do you fix a toilet that is moving side to side?

1. Check the Bolts First. Sometimes a rocking toilet can be fixed by tightening the two flange bolts, or closet bolts, at the base of the toilet. …
2. Look for Leaks. Confirm that your toilet is not leaking. …
3. Locate the Gaps. …
4. Insert the Shims. …
5. Trim the Shims. …
6. Caulk Around the Base. …
7. Let the Caulk Dry.

Is it possible to move a toilet in a bathroom?

Moving a toilet is not a straightforward weekend DIY job, but it is very doable when you involve the professionals. Once the toilet itself is removed, your plumber will have to move the drainage, as well as the water supply to accommodate the new location.

Can you switch a toilet and shower?

It’s not – well, they’re going to drain to the same place but you would have to reconfigure the plumbing. So it’s not quite that easy to swap toilet, shower locations but not impossible. … Because switching those is a big job; you’re going to have to tear up the floor to do the plumbing.

What is toilet stack?

The stack is considered a main drain line. It collects and distributes wastewater from all those smaller pipes to the main house drain. Your waste water then travels to the house sewer, the city sewer line, then to the public sewer treatment facility.

How far is toilet from wall?

Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

Can a toilet and shower share the same vent?

Wet vents are typically used when plumbing a bathroom group. So yes the shower can also be vented by the wet vent along with the toilet. There is one major stipulation when wet venting multiple fixtures when a toilet is one of them: the toilet must be the last fixture connected to the wet vent.

Does vent stack have to be straight?

Vent pipes must be installed so they stay dry. This means that they should emerge from the top of the drainpipe, either straight vertically or at no less than a 45-degree angle from horizontal, so that water cannot back up into them.

Can a vent stack run horizontal?

To answer your specific question, yes, vent pipes can have horizontal runs, as long as there is no possibility of them becoming plugged with water. In other words, any water that gets into the vent pipe opening must be able to run freely all the way to the sewer, without creating a “trap”.

Can P trap be lower than drain pipe?

You attach the p-trap directly to the drainage and manuever the p-traps exits into you existing drain. It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times.

How far should vent be from P trap?

trap, the distance from the weir of the trap to the vent pipe opening “shall not” exceed 30 inches.

How far below the bottom of a sink should the drain pipe be?

Average Distance The standard kitchen sink is 8 inches deep, which means that the normal distance between a kitchen sink drain and the floor is 28 inches. This will vary, depending on the height of the counter and the depth of the sink bowl.

Can you plumb two toilets on the same line?

In answer to the question, yes, two toilets can share the same drain line but not the same drain hole.

How many DFU is a toilet?

A toilet only produces 3 DFUs.

What size is the main sewer line?

Sewer drains from laundry sinks or washing machines are 2 inches in diameter and those from sinks in the kitchen, bathroom or powder room generally use a 1.5-inch pipe. The main sewer pipe leading to the septic tank or public sewer is usually 4 inches.

How far can a soil pipe run?

longest run for horizontal soil is 6 metres, but what about when u add bends.

Why would I want an elongated toilet bowl?

Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.

Can a toilet touch the wall?

Toilets should have a minimum of 15 inches from walls that flank the fixture. A distance of 12 to 12.5 inches should be between the center of the toilet flange and the back wall.

What does 12 rough-in for toilet mean?

The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. … Rear-outlet toilets are configured a bit differently.

How far can a toilet flange be above the floor?

The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal. If you recently tiled or changed the bathroom flooring, the flange height is likely less than optimal.

Can a toilet flange be too high?

When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.