How wide are dressers

A standard dresser has between six and nine drawers, is around waist tall (26″ – 44″), is 36″ – 60″ wide, and is 16″ – 20″ deep. However, these can vary and you should choose an option that works best in your bedroom. To find the right dresser dimensions for you, decide where you’d like your dresser to go.

How wide is a chest of drawers?

Although there is no standard size for a chest of drawers, the most common size is 38 inches wide. A chest of drawers this size is small enough to fit in most bedrooms, but large enough to have ample storage space.

How wide should dresser drawers be?

Dresser drawers should be no more than 36 inches wide. Specifically, states Squidoo.com, a “standard size pine chest of drawers” is typically sized in either “17-inch width, 24-inch width, 30-inch width or 36-inch width” drawers.

How wide is a tall boy dresser?

The Raleigh Tall Dresser has an overall height of 50.5” (128 cm), width of 30.5” (77 cm), and depth of 18.75” (48 cm).

How deep should a dresser drawer be?

The depth of any dresser is approximately 16 to 22 inches. The greater depth provides more stability needed in taller chests or dressers with mirrors attached to them. Drawers pull out 10 to 12 inches for use, so add that measurement to the depth when planning where to place your dresser.

How are dressers measured?

A dresser is defined as a piece of furniture with six, seven or even nine drawers that is roughly waist-high and wider than it is tall or deep. The typical, rectangular dresser usually measures about 60 inches wide, 20 inches deep, and 30 inches tall. … The standard dresser height is usually between 30 and 36 inches.

What is the average drawer depth?

Depth: Standard depths are 14-inches, 16-inches and 20-inches. Height: The height of the drawer refers to the height of the drawer face.

What is the length of a triple dresser?

Elegant triple dresser is over 8 feet long, with modern, clean lines and a sleek look that will make your bedroom the envy of all the neighbors. Nine drawers to hold all your wardrobe essentials and then some.

What are the dimensions of a nightstand?

Nightstands are usually square and come in pairs: one for each side of the bed. An average nightstand measures around 20″ wide and 20″ deep. The height of the nightstand should be equal — or close to — the height of your bed frame and mattress so that the pieces align properly.

How are dresser drawers measured?

Open the drawer all the way and remove its contents. Use a measuring tape to measure the floor of the drawer; measure from the left to the right and from the back of the drawer to the side closest to you. Note that drawers may not be built on a straight axis, so measure at the middle and ends to cover all ground.

Article first time published on

How do you find the area of a drawer?

Measure the height and width of the drawer opening and add 1-1/2 inches to get the face size of the drawer. For example, if the drawer opening measures 18-by-22 inches, you will need to cut one piece 3/4-by-19 1/2-by-23 1/2 inches.

How wide are most dressers?

A standard dresser has between six and nine drawers, is around waist tall (26″ – 44″), is 36″ – 60″ wide, and is 16″ – 20″ deep. However, these can vary and you should choose an option that works best in your bedroom. To find the right dresser dimensions for you, decide where you’d like your dresser to go.

How deep are chest drawers?

How big are dressers? Dressers come in a large range of sizes to meet varied storage demands, but dressers commonly have overall depths between 18”-24” | (46-61 cm), heights between 30”-50” (76-127 cm), and widths between 30”-74” (76-188 cm).

How deep should bedroom drawers be?

Drawers for folded clothes should be set at a minimum of 18” (45.7 cm) with deeper drawers for multiple rows of folding clothing at a depth of 24” (61 cm). Deep drawers are consistent with standard closet depths 24” (61 cm).

How do you determine drawer size?

Measure from the back of the drawer-front to the end of the drawer box. Only measure the box, do not include the drawer front. Round the measurement off to the lower number on the tape. For example, when the measurement is 22 1/2 inches, you need to purchase 22-inch drawer slides.

What size are kitchen drawers?

Standard non-custom kitchen cabinetry generally offers drawer widths from 12 inches to 24 inches, increasing by 3-inch increments. If the standard drawers available don’t fit into your kitchen design, you can order custom drawers from a cabinetmaker.

What is the average width of a bedside table?

The average measurements of a bedside table or nightstand are 20 inches in height, 20 inches in width, and 20 inches in depth. This provides more than enough room for a lamp, book, and clock.

What size are bedside cabinets?

Bedside Tables have average heights between 24”-28” (61-71 cm) to match typical bed heights of 25” (63.5 cm).

How wide is a master bed?

The average size of a master bedroom is 14 x 16 feet. It may be bigger than that but 224 square footage is a minimum.

How wide is a 9 drawer dresser?

W x 11.73 in. D.

What makes a triple dresser?

a dresser having three drawers across for most of its height.

What is a double dresser?

noun Furniture. a dresser having two long drawers across its width for most of its height.

How do you measure cabinet width?

Measure the narrowest width, between your hinges, of the cabinet. If you only have one door or a center frame, measure from the hinge to the frame. Our units have drawers that will extend out of your cabinet. You will use the width dimension to determine which and how many units will fit side-by-side in your space.

What is the width of a filing cabinet?

Cabinets have 2, 3, 4, or 5 drawers, and are made for either letter-size paper or legal-size paper. Letter-size cabinets are typically 15 inches wide and legal size are 18¼ inches wide. The typical office vertical file cabinet is 28½ inches deep and the drawer holds 27 inches of files.

How much is plywood for drawers?

The sides and back of the drawer should be 1⁄2” or 5⁄8” thick. Use thinner stock for smaller drawers and thicker stock for big ones. The bottom is usually 1⁄4“-thick plywood for small drawers or 1⁄2“-thick material for bigger drawers, or drawers that will hold heavy objects.

How do you find the square footage of a dresser?

Step 1: Measure the width of your item in inches and then multiply times the height. Step 2. Multiply the width and height of all sides to be coated (including the top). Step 3: Add all of these totals together and divide by 144 to determine the total square feet you will need to cover.

What is length and width?

Length is describing how long something is while width is describing how wide an object is. 2.In geometry, length pertains to the longest side of the rectangle while width is the shorter side. … Length can also refer to an extent of time or a measure of distance. 4. The most common unit for measuring length is the meter.

Whats the difference between a chest of drawers and a dresser?

First, you should know the difference between a chest of drawers and a dresser. … However, a dresser is usually wide and short, while a chest of drawers is narrow and tall. Dressers are meant to provide a space you can dress in front of – the top serves as a table to place clothes and provides space for a mirror.

How do I stop my drawer bottoms from falling out?

Apply a uniform bead of wood glue to the recess on the detached back piece of the drawer. Apply wood glue to the sides of the drawer at the ends where the back will attach. Fit the back edge of the drawer bottom into the recess on the back piece and push the piece into place.

What can I use for drawer bottoms?

The most common materials for drawer bottoms are 1⁄4″ hardboard or plywood. For small and medium-size drawers, hardboard will stand up to a moderate amount of weight. For a heavier load, you can step up to plywood. Baltic birch plywood is a great choice.